Lantronix Matchport Breakout Board
Product Description
The pins on the Matchport module do not match up to the standard .1" spacing normally found on prototyping boards. This breakout board allows easy access to the pins on the Lantronix Matchport network module by adapting them to the familiar standard. Module not included. Soldering required if purchased in kit form.
Lantronix Matchport Breakout Assembled- $11.99 |
Lantronix Matchport Breakout Kit- $9.99 |
Lantronix Matchport Breakout PCB - $3.99 |
Product Description
This board will convert TTL level locic to RS232 standards and vice versa for use in microcontroller to PC communication. Just connect a standard 9 pin serial cable to the 9 pin connnector and the header pins to your proto board to begin communication. The kit version requires soldering.
MAX232 Breakout Assembled - $11.99 |
MAX232 Breakout Kit - $9.99 |
MAX232 Breakout PCB - $3.99 |
Product Description
This breakout board will allow you to breakout the SD/MMC socket to a standard .1" 10-pin header. Perfect for breadboarding and the likes. Board comes fully assembled and tested as shown.
SD Breakout - $16.99 |
Product Description
This is the SparkFun USB to Serial Breakout for the FT232RL, a small board with a built in USB to serial UART interface. This little breakout is built around the FT232RL IC from FTDI, with an internal oscillator, EEPROM, and a 28-pin SSOP package this is a serious little chip.
FT232R - $13.99 |
Product Description
8, 16, 20, and 28-Pin SSOP to DIP break out boards. The footprint was rotated to accommodate different width SSOP devices and can be used with any pin count up to 28 pins. Designed to be used with 0.65mm pitch devices but can also be used with 0.025" pitch devices (comes out to ~0.635mm). We’ve made these 0.635mm devices fit just fine. Can be used with packages that have a lead span of .230" up to .350". Breaks out SSOP pins to standard .6" (600mil) and .3" (300mil) DIP width to be used in any DIP socket or bread board. The 8 and 16 boards have a 300mil spacing. The 20 and 28 pin boards have 600mil spacing between the DIP pins.
40 Pin break-away headers are perfect for use with these custom PCBs. Machine pin headers may be a better option for IC sockets. Pad layout fits all standard SSOP .65mm and can accommodate .635mm pitch devices.
SSOP to 28 pin DIP - $3.49 |
Product Description
We have no idea what USB device you are hooking up to, but if you want to access the microUSB port on something, you might want this. We broke out all 5 pins with a vertical microUSB connector for your prototyping needs.
USB MicroB Plug- $3.49 |
Product Description
This simple board breaks out a micro-B USB connector’s VCC, GND, ID, D- and D+ pins to a 0.1" pitch header. If you want to add the popular micro-B USB to your project, but don’t want to put up with soldering the tiny connector, this is the board for you.
MicroB USB- $3.49 |
Product Description
We do lots of converting from TTL serial to USB (using the FTDI and Silicon Labs ICs). But what do you do if you’ve got a laptop and need RS232 serial? This is a high quality, low cost, small, and easy to use USB to RS232 converter. Device uses the Prolific IC PL-2303 and supports baud rates up to 1Mbps. Driver support for Windows, Mac, and Linux RedHat.
This converter plugs directly into your USB port on your computer and even comes with a small extension cable and CD for drivers.
USB to RS232 - $7.99 |
6 Pin FTDI USB to TTL Serial Converter
Product Description
This cable provides a fast simple way to connect devices with a TTL level serial interface to USB. The cable features a 6-way SIL, 0.1" connector that provides TTL levels at 3.3V.
Red Wire: 5V
Black Wire: GND
White Wire: RXD
Green Wire: TXD
Yellow Wire: RTS
Blue Wire: CTS
FTDI USB to TTL Serial - $7.99 |